上海索强流体控制岛网设备有限公司

气动柱塞泵

美国技术气动柱塞泵、气动插桶泵、气动泵

◆产品概述◆

本产品是欧洲技术与东方智慧的完美结合，是引进美国气动柱塞泵制造技术及工艺进行改良而研制成功的新一代国际最先进泵类产品，是索强公司技术人员和美国专家共同研究的成果，可用于任何流体输送、注入和抽空。

“气动柱塞泵”（简称：气动油桶泵，又名：气动插桶泵，气动泵、气动活塞泵、气动浆料泵，气动浓浆泵，气动往复泵，气动打胶泵、气动抽液泵，气动防爆不锈钢泵，皮革喷浆泵）

Pneumatic plunger pump

The United States of America Technology pneumatic plunger pump, pneumatic barrel pump, pneumatic pump

◆Product overview◆

This product is a European technology and Oriental wisdom of the perfect combination, is the introduction of the United States of America pneumatic plunger pump manufacturing technology and process are improved and the successful development of a new generation of the most advanced pump products, is the Suo Qiang company technical personnel and American experts to study the results, can be used for any fluid transfer, injection and evacuation.

Pneumatic pulp pump (short for pulp pump, also known as leather pulp spray pump, high-viscosity pulp pump, pneumatic pumping, pneumatic paint pump, pneumatic plug pump, pneumatic prevent explosion inserting the barrel pump, pneumatic intercourse pump)

定制各种型式进出接口、泵连接管尺寸及流量大小控制

Customize the various patter of passing in and out joints and the kinds of dimension of the pipe connecting pump

一、用途
气动柱塞泵应用于人造革、移膜革、压延革、彩涂板、印染、医药、涂层、化工、纺织、喷漆、喷涂、薄膜镀铝、彩钢瓦等行业。适用于高粘度（VIS）≤12万CPS/25℃的化工浆料输送，具有防爆耐腐防沉淀、低噪音、节能等功能。是理想的移动输送设备。
One, use

Pneumatic plunger pump used in leather, leather shift membrane leather, calendering, Cai Tuban, printing and dyeing, medicine, coating, chemical, textile, paint, coating, thin aluminized, color-coated steel tile industry. Suitable for high viscosity ( VIS ) is less than 120000 CPS / 25 C chemical slurry, with explosion-proof corrosion preventing sedimentation, low noise, energy saving and other functions. Is the ideal mobile conveying equipment.

二、使用方法
　　1、先将导料管正确放入所要输送的料桶内。
　　2、将耐腐蚀软管连接出料口接至送料地点。
　　3、进气阀呈关闭状态，然后将气源管连接进气阀接头，根据所需浆料流量来开启进气阀　　调节气动浆料泵运行频率，即可工作。
Two, the use of methods

In 1, the first material guide pipe correctly in order to transport the material barrel.

In 2, the corrosion resistant hose outlet connected to a feeding place.

In 3, the inlet valve is closed, and then the air tube connected to the inlet valve joint, depending on the desired slurry flow to open the intake valve regulated pneumatic slurry pump running frequency, can work.

三、维护保养
　　1、气动浆料泵在使用过程中防止撞击缸体部位避免变形，发生活塞卡死现象，造成报废。
　　2、活塞在运行壹佰万余次后，根据空压机送气过程中水份积留情况应清缸体，涂注30#润滑油。
　　3、如经久不用，应在溶剂内工作状清洗，防止浆料冻结，阻塞导料管。Three, maintenance

1, pneumatic slurry pump in use in the process of collision avoiding deformation of cylinder, piston clamping phenomenon occurs, causing scrap.

In 2, the piston in the operation Yibaiwanyu times, according to the air compressor in the process of accumulation of water supply should be clear and cylinder, with 30 # lubricating oil.

3, if is not, should be in a solvent cleaning work shape, prevent the slurry freeze, blocking material guide pipe.

四、注意事项
　　1、在工作中，如缸体部位发热（以手感热为准），应立即加30#润滑油。
　　2、使用过程中如调节螺母松动，发生漏料，应及时调整螺母。

four, the matters needing attention

1, in the work, such as cylinder part of heat ( with hot date), should immediately plus 30 # lubricating oil.

2, the use of the process as the regulating nut loosening occurred, leakage, timely adjust nut.

五、结构和原理
　　本产品采用气压差的作用，使活塞上下运行，带动导料活塞开闭，起到提料的作用。调整给气动浆料泵工作气体的流量与气压来控制和调节气动浆料泵送料流量。结合感应开关能使之自动化工作。

Five, structure and principle

This product is the role of pressure difference, so that the piston moves up and down, expected to lead the pistons led off, played the role of reference materials. Adjustment to the slurry pump pneumatic gas flow and pressure to control and adjust the slurry pump pneumatic feeding flow. Combined with inductive switch can make the automation work.